Diodes

Product Details:

The LM317LIPK is an adjustable 3-terminal Positive Voltage Regulator, capable of supplying 100mA over an output-voltage range of 1.25 to 32V. It is exceptionally easy to use and requires only two external resistors to set the output voltage. The LM317LIPK device is a 100mA linear regulator with high voltage tolerance up to 35V. The device has a feedback voltage that is relative to the output instead of ground. This ungrounded design allows the LM317L device to have superior line and load regulation. This design also allows the LM317LIPK device to be used as a current source or current sink using a single resistor. Any output voltage from 1.25 to 32V can be obtained by using two resistors. The bias current of the device up to 2.5mA, flows to the output, this current must be used by the load or the feedback resistors. The power dissipation is the product of pass-element voltage and current.

• Output voltage range adjustable 1.25 to 32V when used with external resistor divider
• Output current capability of 100mA
• Input regulation typically 0.01% per input-voltage change
• Output regulation typically 0.5%
• Ripple rejection typically 80dB
• For higher output current requirements
• Green product and no Sb/Br

Applications

Commercial, Medical, Computers & Computer Peripherals, Consumer Electronics

Product Details:

Direct triggering from low power drivers and logic ICs • High blocking voltage capability • Low holding current for low current loads and lowest EMI at commutation • Planar passivated for voltage ruggedness and reliability • Sensitive gate • Surface-mountable package • Triggering in all four quadrants 3. Applications • General purpose motor controls • General purpose switching 

Product Details:

Hornby 1N4007 Diode Description

The 1N4007 is a general-purpose rectifier diode used in power supply circuits, voltage rectification, and protection applications. It is part of the 1N400x series, which is widely used in AC-to-DC conversion and low-frequency rectification.

Key Features:

✅ Diode Type: General-Purpose Rectifier
✅ Manufacturer: Hornby (or equivalent brands like CDIL, ON Semiconductor, Vishay, etc.)
✅ Maximum Repetitive Reverse Voltage (Vrrm): 1000V
✅ Forward Current (If): 1A (continuous load)
✅ Surge Current (Ifsm): 30A (for 8.3ms half-sine pulse)
✅ Forward Voltage Drop (Vf): 1.1V (at 1A current)
✅ Reverse Recovery Time: ≤30µs
✅ Package Type: DO-41 (Through-Hole Axial Lead Package)
✅ Operating Temperature Range: -55°C to +150°C

Applications:

�� AC-to-DC Rectification: Used in bridge rectifiers and power adapters.
�� Voltage Blocking & Polarity Protection: Prevents reverse polarity damage in circuits.
�� Freewheeling Diode: Used in motor driver circuits to suppress voltage spikes.
�� Low-Frequency Rectification: Suitable for 50Hz/60Hz rectifier applications.
�� LED & Battery Protection Circuits: Ensures proper current flow and voltage regulation.

Product Details:

A 100?H I-shaped magnetic core inductor with dimensions of 8x10 mm and a hole mount configuration is a specific type of electronic component used in electrical circuits, particularly in applications where filtering, energy storage, or impedance matching is required.Let's break down the information:100?H: This indicates the inductance value of the inductor, measured in Henrys (H). Inductance is a measure of an inductor's ability to store energy in a magnetic field when current flows through it. 100?H means 100 microhenries.

I-Shaped Magnetic Core: The "I-shaped" core refers to the physical shape of the magnetic core around which the wire is wound. This core is usually made of a magnetic material like iron or ferrite, and it enhances the inductor's ability to store energy efficiently.

8x10 mm: These are the physical dimensions of the inductor. It's 8 millimeters in width and 10 millimeters in length. This indicates the size of the component, which is important for fitting it into a circuit or on a circuit board.

Hole Mount: This indicates the method by which the inductor is mounted onto a circuit board or other surface. A hole mount means that the component has leads or pins that are meant to be inserted into holes on a circuit board, and then soldered in place to secure it.ApplicationThe 100uH I-shaped magnetic core inductor with dimensions of 8x10 mm is a compact passive component commonly used in electronic circuits to store and release energy in the form of a magnetic field. It offers an inductance of 100 microhenries (uH), making it suitable for various applications requiring moderate inductance levels.Technical Details

• Model: DIP Power Inductor
• Value of Resistance: 2.2UH ~ 100MH
• Size: 8x10 mm
• Induction: L 1-22uh ± 10%
• Number of turns: 20.5T
• Wire: copper wire
• Wire gauge: 2UEW 0.27mm
• Magnetic core: Ferrite
• Temperature: -20°C ~ +80°C

Physical Attributes

• W x H (mm): 8 x 10
• approx Weight: 2 gm

Package Includes

• 1 x 100uH I-Shaped Magnetic Core Inductor 8x10 mm